LED sorting technology

The human eye has a very high resolution for the color and brightness of light, and is particularly sensitive to differences and variations in color. The sensitivity of the human eye to different wavelengths of light is different. For example, for a wavelength of 585 nm light, when the color change is greater than 1 nm, the human eye can feel it; and for a red light with a wavelength of 650 nm, when the color changes at 3 nm, the human eye can perceive it.

In the early days, since LEDs were mainly used as indicators or display lamps, and generally appeared as a single device, the control of sorting and brightness of their wavelengths was not high. However, as the efficiency and brightness of LEDs continue to increase, the range of applications is becoming wider and wider. When LEDs are used as array display and display devices, due to the sensitivity of the human eye to color wavelength and brightness, the use of unselected LEDs will produce unevenness, which will affect people's visual effects. Unevenness in wavelength and brightness can give people an uncomfortable feeling. This is something that LED display manufacturers are not willing to see, and it is unacceptable to people. LEDs are usually tested and sorted according to several key parameters such as dominant wavelength, luminous intensity, luminous intensity, color temperature, operating voltage, and reverse breakdown voltage. LED testing and sorting is a necessary process in the LED production process. At present, it is the capacity bottleneck of many LED chips and packaging manufacturers, and is also an important part of LED chip production and packaging costs.

1, LED sorting method

There are two ways to sort LEDs: one is chip-based test sorting, and the other is to test and sort the packaged LEDs.

(1) Test separation of chips

LED chip sorting is very difficult, mainly because LED chips are generally small in size, from 9mil to 14mil (0.22-0.35nm). Such a small chip requires a microprobe to complete the test, and the sorting process requires an accurate mechanical and image recognition system, which makes the cost of the device high and the test speed is limited. The current price of the LED chip test sorter is about 1 million yuan, and the test speed is about 10,000 per hour. If calculated according to 25 days per month, the capacity of each sorter is 5KK per month.

At present, there are two methods for chip sorting: one method is to test sorting by the same machine, its advantage is reliable, but the speed is very slow, the productivity is low; the other method is to test and sort by two After the machine is completed, the test equipment records the position and parameters of each chip, and then transfers the data to the sorting device for quick sorting. The advantage of this is that it is fast, but the disadvantage is that the reliability is relatively low and error-prone. Because there is usually a process of substrate thinning and chip separation between the two steps of testing and sorting, in this process, the epitaxial wafer may be chipped, partially broken or partially broken, so that the actual chip The distribution does not match the data stored in the sorter, making sorting difficult.

The key to fundamentally solving the bottleneck problem of chip test sorting is to improve the uniformity of the epitaxial wafer. If the epitaxial film has a wavelength distribution within 2 nm and the brightness changes within +15%, all the chips on the film can be classified into a single file (Bin), as long as the failed chip is removed by testing. Will greatly increase the chip's capacity and reduce the cost of the chip. In the case where the uniformity is not very good, it is also possible to test and replace the chip area with "a lot of unqualified products" by inkjet smearing, thereby quickly obtaining the desired "qualified" chip, but doing so The cost is too high, and many chips that meet the requirements of other rooms will be treated as waste products of non-certificate. The final chip cost may be unacceptable to the market.

(2) LED test sorting

The packaged LEDs can be tested and sorted according to wavelength, luminous intensity, illumination angle, and operating voltage. The result is that the LEDs are divided into a number of bins and categories, and then the test sorting opportunities automatically dispense the LEDs into different Bin boxes according to the set test criteria. Due to the increasing demand for LEDs, the early sorting machine was 32Bin, and later increased to 64Bin. Now there is a 72Bin commercial sorting machine. Even so, the LED specifications of Bin are still unable to meet the needs of production and market.

The LED test sorter tests the LEDs at a specific bench current (eg, 20 mA) and typically performs a reverse voltage test. The current price of the LED test sorter is about 400,000 to 500,000 RMB/set, and the test speed is about 18,000 per hour. If calculated according to the working hours of 20 hours per day for 25 days per month, the capacity of each sorting machine is 9KK per month.

For large displays or other high-end applications, the quality of LEDs is high. Especially in the requirements of wavelength and brightness consistency is very strict. If the LED packaging factory does not impose strict requirements when purchasing the chips, these packaging factories will find that after a large number of packages, only a small number of the packaged LEDs can meet the requirements of a certain customer, and most of the others will change. Into the inventory in the warehouse. This situation forces LED packaging factories to impose stringent requirements when purchasing LED chips, especially for wavelength, brightness, and table voltage; for example, in the past, the wavelength requirement was +2 nm, but now it is required to be +1 nm, even in In some applications, a +0.5 nm requirement has been proposed. This puts tremendous pressure on the chip factory and must be strictly sorted before the chip is sold.

From the above analysis of LED and LED chip selection, it can be seen that the economical approach is to test and sort LEDs. However, due to the wide variety of LEDs, different forms, different shapes, different sizes, different illumination angles, different customer requirements, different application requirements, this use right is completely selected by LED test points. Choosing becomes hard to operate. Moreover, the application of LED is mainly distributed in several wavelength segments and brightness segments. It is difficult for a package factory to prepare LEDs of various forms and types that all customers need. So the key of the problem is back to the epitaxial process of MOCVD, how to The LED epitaxial wafer that grows the required wavelength and brightness is the key point to reduce the cost. If this problem is not solved, the LED production capacity and cost will still not be completely solved. However, before the uniformity of the epitaxial wafer is controlled, a more effective method is to solve the problem of fast and low-cost chip sorting.

2, sorting equipment

At present, LED chip test sorting equipment is mainly provided by US and Japanese manufacturers, and LED test sorting equipment is mostly provided by Taiwanese and Hong Kong manufacturers. There is no manufacturer in China that can provide similar equipment. The LED chip sorting machine mainly includes two major hardware parts (manipulator, micro-probe and photoelectric tester) and a set of system software, and these three parts are respectively provided by different manufacturers and integrated; and the LED test sorting machine includes LED mechanical transmission, storage and photoelectric test two parts.

3, LED sub-selection technology development trend

(1) Develop a fast and low-cost chip sorting process and equipment before the uniformity of the epitaxial wafer is controlled.

(2) With the development of W-class power LED technology, the traditional LED product parameter detection standards and test methods can no longer meet the needs of lighting applications, and new test standards and methods must be developed, including more lighting-related optical content.

(3) In the life test of LED system, develop the long-term performance and rapid measurement and evaluation technology of LED system.

(4) The LED for illumination is operated under high current driving, which puts forward higher reliability requirements. The traditional LED screening method is not suitable for high-power LEDs for lighting. It is necessary to develop new screening test methods to eliminate early failure products and ensure product reliability.

Recess Mounted Led Profile

 

Recess Mounted LED Profile Light have wide application. Size is flexible and can customized. The finish can do oxidation and sandblasting.

 

 

Specification of Surface Mounted Led Profile Light

Product Name: Recess Mounted Led Profile Light

Size: Flexible

Maximum PCB Width: 3.5mm/10mm/12mm

Ribbon inside: Suggest 9.6W/M ribbon inside

Materials: Bar material: 6063 aluminum, with oxide surface

         Cover Material: PC

         End cap material: PC

 Recess Mounted Profile Light

FAQ:

Q1. How do you ship the goods and how long does it take to arrive?
A: We usually ship by DHL, UPS, FedEx or TNT. It usually takes 3-5 days to arrive. Airline  and sea shipping also optional.

Q2. How to proceed an order for led light?


A: Firstly let us know your requirements or application.
Secondly We quote according to your requirements or our suggestions.
Thirdly customer confirms the samples and places deposit for formal order.
Fourthly We arrange the production.

Q3. Is it OK to print my logo on led light product?


A: Yes. Please inform us formally before our production and confirm the design firstly based on our sample.

Q4: Do you offer guarantee for the products?


A: Yes, we offer 2-5 years warranty to our products.

Recess Mounted Led Profile Light

Recess Mounted Led Profile Light,Modern Decorative Track Light,Led Recess Mounted Profile Light,Led Profile Light

Shenzhen Jedver Smart Lighting Co., Ltd. , http://www.jederwell.com